例句與用法

更多例句：  下一頁
1. Electrical analog instruments , panel board types
   配電板式電子模擬設備
2. At present the identification signal of rolling bearing is based on analog monitoring system composed of analog instrument such as fft analyzer , amplitude analyzer and so on . the system has the shortcoming as follows : not enough friendly user interface , unitary function , under abundant analytical contents , poor generality , long developing period , high cost and so forth
   目前對滾動軸承信號識別主要采用模擬監測系統，系統均由模擬量?jī)x器組成，如fft分析儀、幅值分析儀電平記錄儀等，系統存在操作界面不夠友好，功能單一，分析內容欠豐富、通用性差、開發周期長、成本高等缺點。
3. The design of high - voltage circuit based on pwm technology is briefly described . the closed - loop current control theory using analog instruments is fully discussed , followed which is that using digital instruments . it is an important part that the hardware and software design of the single chip - two arms and two chips - two arms current control circuits with a new chip applicable to digital current control system
   簡單介紹了基于開關電源技術的高壓電路設計；詳細講述了模擬穩流電源的閉環穩流原理，并在此基礎上討論了利用數字電路實現穩流的原理及可能性；選擇出適合數字穩流系統的新型芯片，完成了單片雙路穩流系統、雙片雙路穩流系統的軟硬件設計；給出了一種簡單易實現的比例?積分控制程序。
4. Furthermore , the strongly functional programming language labwindows / cvi is well used . the paper is based on the deep analysis of rolling bearing identification technology which is made up of analog instruments . a suit of rolling bearing identification signal virtual instrument has been found with which some representative failure of gb6309 type of rolling bearing on the omnipotent lab desk in testing laboratory have been measured and diagnosed
   本論文在深入分析研究以模擬儀器為基礎的滾動軸承診斷技術的基礎上，應用現代先進的虛擬儀器技術，合理選用傳感器、信號調理器及a / d轉換板等硬件，采用具有強大功能的虛擬儀器編程語言： labwindows / cvi平臺，編寫了一系列功能軟件和軟面板，成功地研制和組建了一套滾動軸承信號識別及工況監測虛擬儀器，并利用所研制的虛擬儀器，在測試實驗室萬能實驗臺上對若干gb6309型號深溝滾動軸承的幾種典型故障進行了實際檢測與診斷，收到了滿意的效果。
5. In this system , the movement of the step - electromotor is controlled by computer , and then the dial pointer is drove by the step - electromotor . at the same time , these images of the analog instrument are took by high precision ccd video , and then these images will be processed by the computer , using some image - processing algorithms such as image segmentations , threshold identification , image binarization , areas labeling , dial center - point identification , useful areas identification & abstracting , and areas thinning , etc . followed this , the dial pointer of the “ circle ” is able to be located . at last , the dial pointer position will be recognized by the computer
   本系統由計算機控制步進電動機的運動,進而驅動指針式儀表表針的運動,并且通過高精度ccd攝像機實時獲取表盤圖像數據,同時進行表盤圖像的相關處理,包括圖像分割,閾值確定,圖像二值化,區域標記算法,圓心擬合,有效區域識別提取,區域細化等,最終快速識別出表盤指針?biāo)幬恢?最后,根據國家指針式儀表類檢定規程所制定的算法計算出該儀表的相關誤差,檢定指針式儀表的各種精度,通過這些數據判斷該儀表是否合格,打印該儀表的檢定結果報表。